Fitting Guide - Bailey Back Plate Assembly

Back PLATE Front end

Associates INSTRUCTIONS: XENITH SHOULDER PADS


HARDWARE CONTENTS

  • two Zipper Straps
  • 2 Elastic Hardware Covers
  • 4 T-Nuts
  • four Screws

Pace one

Feed lower cease of zipper strap with two grommets through slot in back plate from exterior to inside. Select inner or outer slot to all-time match up with holes in shoulder pad.

STEP 2

Place elastic hardware cover onto attachment strap.

Pace three

Feed upper end of attachment strap through slot in shoulder pad from outside to inside.

STEP 4

Feed upper stop of attachment strap back through elastic hardware embrace.

STEP 5

Marshal the two grommet holes on the lower end of the attachment strap with one of the grommet holes from the upper end, and place a t-nut through the 3 grommet holes from back to front end. The vertical position of the pad can be adjusted using the different grommet holes.

STEP 6

Install screw through front of grommet holes into t-nut and tighten.

Stride 7

Slide rubberband hardware comprehend over t-nut and screw. Repeat process from step ane for other attachment strap location.

Back PLATE BACK

ASSEMBLY INSTRUCTIONS: Not-XENITH SHOULDER PADS

HARDWARE CONTENTS

  • iv Zipper Straps
  • 4 Rubberband Hardware Covers
  • viii T-Nuts
  • 8 Screws

Stride 1

Feed lower end of attachment strap with ii grommets through slot in back plate from outside to within. Select inner or outer slot to best match up with slots in shoulder pad.

STEP two

Place elastic hardware cover onto attachment strap.

Step three

Identify a t-nut through the two lower grommet holes in the strap from back to front.

STEP 4

Install spiral through front of grommet holes into t-nut and tighten.

Stride 5

Depending on the shoulder pad model used, select an existing pigsty, or a pigsty may demand to exist drilled. NOTE: Drilling your shoulder pad may void the warranty or cause damage; practice and so merely at your own take a chance. Feed a t-nut through the hole in the shoulder pad from the back, and through a chosen grommet hole in the attachment strap. Pad position can be adjusted by choosing different holes. Install a screw through the grommet hole and into the t-nut to secure the back plate.

STEP vi

Slide elastic hardware encompass over t-nut and screw. Echo process from step 1 for other attachment strap location.

BACK PLATE FRONT

ASSEMBLY INSTRUCTIONS: XENITH SHOULDER PADS

HARDWARE CONTENTS

  • 2 Attachment Straps
  • 2 Elastic Hardware Covers
  • 4 T-Nuts
  • four Screws

STEP 1

Feed lower end of attachment strap with two grommets through slot in back plate from exterior to inside. Select inner or outer slot to best lucifer upwards with holes in shoulder pad.

Footstep 2

Place elastic hardware cover onto attachment strap.

STEP 3

Feed upper cease of attachment strap through slot in shoulder pad from exterior to inside.

STEP 4

Feed upper finish of attachment strap dorsum through elastic hardware cover.

STEP v

Align the two grommet holes on the lower end of the attachment strap with one of the grommet holes from the upper end, and place a t-nut through the iii grommet holes from dorsum to front. The vertical position of the pad tin be adjusted using the unlike grommet holes.

Pace six

Install screw through front of grommet holes into t-nut and tighten.

STEP 7

Slide elastic hardware embrace over t-nut and screw. Repeat process from step 1 for other attachment strap location.

BACK PLATE Back

Associates INSTRUCTIONS: Non-XENITH SHOULDER PADS


HARDWARE CONTENTS

  • 2 Attachment Straps
  • ii Elastic Hardware Covers
  • iv T-Nuts
  • four Screws

STEP 1

Feed lower terminate of attachment strap with two grommets through slot in back plate from outside to inside. Select inner or outer slot to all-time match up with holes in shoulder pad.

Pace ii

Place rubberband hardware cover onto attachment strap.

STEP 3

Feed upper stop of attachment strap through slot in shoulder pad from outside to inside.

STEP 4

Feed upper stop of zipper strap back through elastic hardware cover.

Stride 5

Align the ii grommet holes on the lower cease of the attachment strap with one of the grommet holes from the upper end, and identify a t-nut through the three grommet holes from back to front. The vertical position of the pad can be adjusted using the unlike grommet holes.

Stride half dozen

Slide elastic hardware cover over t-nut and spiral. Repeat procedure from step 1 for other attachment strap location.

Downloads

Download a copy and study it like your playbook.

Download the manual →